Instrument Sterilization Training for Dental Offices
What it is
Instrument sterilization is the step-by-step process of making reusable dental instruments safe for the next patient. It includes cleaning, inspecting, packaging, heat sterilizing, monitoring the sterilizer, and storing instruments properly. Each step has to happen correctly and in the right order, every time.
Sterilization training teaches the team members who process instruments how to do each step, how to read biological, chemical, and mechanical indicators, and what to do when a test fails. Broader topics like hand hygiene, surface disinfection, and waterlines are covered on our Infection Control page.
Why your office needs it
Who should be trained. The CDC recommends that cleaning, disinfection, and sterilization be assigned only to staff who are trained in the required reprocessing steps, including the right PPE for handling contaminated instruments.
What CDC guidance expects. There is no single federal training rule just for sterilization, but the CDC’s dental infection control guidance sets clear expectations:
- Heat sterilize critical items, such as surgical instruments and periodontal scalers, and heat-tolerant semicritical items, such as mouth mirrors.
- Heat sterilize dental handpieces between patients, including low-speed motors and reusable prophy angles. Surface or high-level disinfection is not enough.
- Clean before sterilizing. Leftover blood and debris can shield microorganisms and make sterilization fail.
- Label packages with the sterilizer used, the cycle or load number, and the date, so items can be recalled if there’s a failure.
- Use a chemical indicator inside every package, and an external indicator if the internal one isn’t visible.
- Spore test sterilizers at least weekly, along with mechanical and chemical monitoring.
- Keep sterilization and maintenance records according to state and local regulations.
- Follow manufacturer instructions for every instrument and sterilizer.
Instrument processing also involves sharps and contaminated items, so OSHA’s Bloodborne Pathogens Standard applies to the staff who do it. See our OSHA & Bloodborne Pathogens page.
How often training is recommended
The CDC recommends infection prevention training, which includes instrument processing, at orientation, when new tasks or procedures are introduced, and at a minimum annually. Retrain whenever you add a new sterilizer, a new instrument type, or a new staff member to processing.
State requirements vary. Your State Board may have its own rules on sterilizer monitoring or on how long to keep sterilization records. Check with your State Board for what applies to your office.
What can happen if sterilization fails
These are real, documented cases.
- 7,000 patients told to get tested (2013). Health inspectors went to an oral surgery practice after a patient with no other known risk factors tested positive for hepatitis C and HIV. The state dental board’s complaint said the sterilizer wasn’t working properly and that the required lab spore test had never been done in the six years one assistant had worked there. Inspectors also found a separate set of rusty instruments used on patients known to have infectious diseases. Letters went to 7,000 patients recommending testing for hepatitis B, hepatitis C, and HIV. Source: CBS News
- 1,812 patients notified after reprocessing errors (2010). An inspection of a dental clinic found 21 unacceptable infection control conditions. Soiled instruments were packaged for sterilization without proper cleaning, items were visibly dirty after sterilization, packs were wet, and some items were packaged for the wrong sterilization method. Standard operating procedures and staff competency records weren’t available. 1,812 patients were identified as potentially affected and offered testing. Source: VA Office of Inspector General and St. Louis Public Radio
The CDC notes that in documented disease transmissions in dental settings, reported breakdowns included failure to heat sterilize handpieces between patients and failure to spore test sterilizers. Source: CDC
How Dynamic Dental Safety helps
- Full office evaluation. We walk through your sterilization area and workflow, from cleaning and packaging to spore testing and storage, and give you a written report of any issues.
- On-site staff training with CE. We train the people who process your instruments, at your office, on your equipment. Our training counts toward state dental CE requirements because Dynamic Dental Safety is an ADA CERP provider.
- Materials, templates, and documentation. Sterilization logs, spore test records, and step-by-step procedures your team can follow.
- Year-round consultation. Unlimited consultation, including when a spore test fails and you need to know what to do next.
Make sure every instrument is ready for the next patient.
